Boiler Fault Codes
Fault codes indicate that the boiler has detected a problem with a system, component or operating condition.
For example, an older Baxi model may display E119 when system water pressure is too low.
Example: E119Is your Baxi boiler displaying an error code or refusing to start? Find common Baxi fault codes, including E119, E133, E125 and E160. Learn what they mean, which checks are safe to carry out and when to contact a Gas Safe registered engineer.
Illustrative display only. Fault-code formats and meanings vary by Baxi model.
Find the code displayed on your Baxi boiler and expand it to see what it may indicate, possible causes and appropriate next steps. These explanations cover codes used on selected Baxi boiler ranges. Always check the manual for your exact model, as meanings and reset procedures can differ.
Meaning: The heating system pressure is too low for normal operation.
Possible causes: Water loss, a leak or insufficient system pressure.
What to do: Check the pressure reading and follow your model's instructions for repressurising, if permitted. Recurring pressure loss needs investigation.
Meaning: The boiler has failed to establish or detect the required flame.
Possible causes: Gas supply interruption, ignition components or flame detection problems.
What to do: Check the model-specific instructions. Do not attempt gas or combustion repairs. Repeated lockouts require a Gas Safe engineer.
Meaning: The boiler has detected a circulation or temperature-related operating problem.
Possible causes: Restricted water circulation, pump problems or air within the system.
What to do: Arrange professional diagnosis if the code persists or returns.
Meaning: A problem has been detected with the boiler fan or its operation.
Possible causes: Fan failure, wiring or control issues.
What to do: Do not remove the boiler casing. Arrange inspection by a qualified engineer.
Meaning: A safety temperature limit has been reached or a safety thermostat has operated.
Possible causes: Overheating, restricted circulation or a component fault.
What to do: Allow the appliance to remain off and follow the manufacturer's guidance. Persistent faults need professional attention.
Meaning: System water pressure is above the acceptable operating range.
Possible causes: Overfilling, expansion vessel issues or another pressure-control problem.
What to do: Check the gauge and your boiler manual. Do not operate valves or release pressure unless the instructions specifically permit it.
Meaning: Low heating-system pressure on certain Baxi boiler models.
Possible causes: Water loss, leaks or insufficient system pressure.
What to do: Check the manual for your exact model before attempting any pressure adjustment.
Meaning: Flame loss has been detected during boiler operation.
Possible causes: Combustion, flame detection or gas supply-related problems.
What to do: Persistent flame-related faults require a Gas Safe registered engineer.
Meaning: A flue temperature safety condition has been detected.
Possible causes: Excessive flue temperature or an associated component problem.
What to do: Do not attempt flue or combustion system repairs. Arrange professional inspection.
Meaning: A boiler control or electronic component fault has been detected.
Possible causes: Control board or associated electrical issues.
What to do: Arrange qualified diagnosis rather than attempting internal electrical repairs.
Meaning: On some Baxi boilers, E168 is associated with an underlying fault or a previously recorded error.
Possible causes: Different electrical or operational faults depending on the boiler model.
What to do: Note any earlier codes and arrange diagnosis if the problem persists.
Meaning: A central-heating temperature sensor fault on selected Baxi models.
Possible causes: A faulty sensor, wiring or connection issue.
What to do: Internal sensor and wiring checks should be performed by a qualified engineer.
Newer Baxi boiler ranges, including some Combi 2 models, may display codes in a different format. Instead of a traditional E-number such as E119, you may see a code containing letters, numbers and full stops. These must be interpreted using the documentation for the exact appliance.
These are examples of newer diagnostic-code formats, not interchangeable equivalents of the traditional Baxi E-codes. Do not assume that a code has the same meaning across different Baxi generations.
A code on your Baxi boiler display does not always mean the same thing. Some indicate a detected fault, others appear when the boiler has stopped operating for safety, and certain displays simply communicate the appliance's current operating status. The exact interpretation depends on the boiler model.
Fault codes indicate that the boiler has detected a problem with a system, component or operating condition.
For example, an older Baxi model may display E119 when system water pressure is too low.
Example: E119A lockout occurs when the boiler prevents further normal operation after detecting a condition that requires intervention.
Some lockouts may allow a manufacturer-approved reset, but recurring lockouts need professional investigation.
Example: E133Not every number, symbol or message on a boiler display indicates a fault.
Depending on the model, the display may show operating temperatures, standby conditions or other normal information. Check the user manual before treating a display as an error.
Model dependentWrite down the complete code, including any letters, numbers or punctuation. A photograph of the display may also help.
Locate the model name using the appliance documentation or accessible identification information. Compare the code with the correct manual.
Only carry out homeowner checks or reset procedures permitted by the manufacturer. Arrange an engineer if the fault persists or returns.
A Baxi Duo-tec, Platinum, Main or newer Combi 2 boiler may use different diagnostic displays. Traditional E-codes should not automatically be applied to newer codes such as A.02.06 or E.04.10. Always use the instructions for your exact appliance.
Some Baxi boiler problems have simple explanations, such as incorrect heating settings or low system pressure. Before arranging a repair, these basic checks may help you understand the issue. Only follow procedures permitted in your boiler's user manual.
Look at the pressure gauge or digital reading, if your model has one. Low pressure may prevent some Baxi boilers from operating normally.
Check your manual for the correct cold-system pressure range.
Make sure your room thermostat is requesting heat and is set above the current room temperature.
Check batteries if your thermostat uses them.
Confirm the boiler display is illuminated and check whether other electrical appliances are working normally.
Do not open the boiler casing or investigate internal wiring.
Check around accessible radiators, pipework and underneath the boiler for signs of dripping or water damage without removing covers.
Never open sealed boiler components to search for a leak.
Check your programmer, heating schedule and selected operating mode. Your boiler may simply not have an active request for central heating.
Confirm that heating has not been switched off by a timer.
Record the exact fault code displayed and compare it with the user instructions for your Baxi model.
Only use a reset procedure if your manufacturer permits it.
Never remove the sealed boiler casing, bypass a safety device or attempt repairs involving gas, combustion or internal electrical components. Repeatedly resetting a boiler without identifying the fault can be unsafe.
If you smell gas in Great Britain: leave the property, avoid using electrical switches or naked flames, and call the National Gas Emergency Service on 0800 111 999 from a safe location.
If the fault code keeps returning, your boiler will not restart or you suspect an internal component problem, Keystone London can help arrange professional fault diagnosis.
A Baxi boiler reset may clear certain temporary faults, but it will not repair a failed component or resolve an ongoing problem. Whether resetting is appropriate depends on the displayed fault code, your boiler model and the manufacturer's instructions.
A reset may be reasonable when the boiler's user manual specifically recommends it for the displayed code and there are no signs of an unsafe condition.
Some faults indicate problems that require proper testing, specialist equipment or internal component inspection.
Record the complete code shown on the display and check it against the instructions for your exact boiler model.
If the manual allows a reset, use only the specified controls. Do not remove covers or attempt internal adjustments.
If the same fault reappears or the boiler does not resume normal operation, stop resetting and arrange professional diagnosis.
Important: Never repeatedly reset a boiler to force it to operate. If you smell gas, suspect a carbon monoxide problem or believe the appliance is unsafe, do not attempt a reset. Leave the affected area and seek emergency assistance as appropriate. In Great Britain, the National Gas Emergency Service can be contacted on 0800 111 999.
Keystone London provides boiler fault diagnosis and repair services across London. If your Baxi boiler keeps locking out or the same code repeatedly appears, contact our team for assistance.
A Baxi fault code often appears alongside a wider heating problem, such as falling water pressure, no hot water or a boiler that will not ignite. Explore our related troubleshooting guides to understand common symptoms, possible causes and when professional attention is needed.
Does your Baxi boiler keep losing pressure or showing a low-pressure warning? Learn about possible causes and what to check.
Read pressure guide →Found water beneath your boiler or around nearby pipework? Understand common leak symptoms and appropriate next steps.
Read leak guide →If your Baxi boiler is not firing up or keeps locking out, explore common ignition problems and when to call an engineer.
Read ignition guide →Is your boiler running but the radiators remain cold or heat unevenly? Explore circulation and heating system issues.
Read radiator guide →Understand why heating system pressure may rise, what high-pressure warnings can indicate and when specialist help is needed.
Read high-pressure guide →Browse our wider boiler error-code guide and find troubleshooting information for other boiler brands and common faults.
Explore fault codes →An Ideal fault code is often accompanied by a noticeable problem, such as low pressure, no hot water or radiators that won't heat up. Explore our practical guides to understand common boiler symptoms and when professional repairs may be needed.
Understand why boiler pressure drops, what you can safely check and when recurring pressure loss needs attention.
Read the guideDiscover common reasons for water leaking from a boiler and the warning signs that should not be ignored.
Read the guideLearn why a boiler may fail to ignite, what ignition lockout means and when to contact a Gas Safe engineer.
Read the guideFind out why radiators may stay cold even when the boiler is running and what might be affecting circulation.
Read the guideUnderstand what high boiler pressure can indicate and when it may point to a heating-system problem.
Read the guideCompare error codes across different boiler manufacturers and explore more troubleshooting information.
Browse fault codesVisit Keystone London's Knowledge Centre for more homeowner guides, boiler troubleshooting advice and practical heating information.
Boiler error codes are specific to the manufacturer and model. If you have a different boiler brand, explore our dedicated fault-code guides for common warnings, possible causes and safe troubleshooting advice.
Understand Worcester Bosch boiler error codes, including common ignition, pressure and temperature-related faults on selected models.
View fault codesExplore Vaillant boiler fault codes, including F.22, F.28 and F.75, with explanations of common operating problems.
View fault codesFind explanations of common Ideal boiler fault and lockout displays, including selected F and L codes.
View fault codesBrowse Keystone London's complete boiler fault-code guide to find manufacturer-specific information and practical advice for common heating problems.
Find answers to common questions about Baxi boiler error codes, low pressure, ignition faults, resets and professional boiler repairs. Fault meanings and procedures can vary between Baxi models, so always consult the correct user manual.
On many Baxi boilers, E119 indicates low heating-system water pressure. The boiler may stop operating until the pressure issue has been resolved.
Check the pressure reading and follow the instructions for your exact model. If the pressure repeatedly falls, there may be a leak or another problem requiring investigation.
E133 commonly relates to an ignition or flame-detection failure on certain Baxi boiler models.
Possible causes include gas supply interruptions, ignition component faults or flame detection problems. If the boiler continues to lock out, arrange inspection by a Gas Safe registered engineer.
On some Baxi models, E168 can be associated with an underlying or previously recorded boiler fault. It does not necessarily identify one specific failed component.
Record any other codes that appeared before E168. If the problem keeps returning, a qualified engineer may need to investigate the underlying cause.
Some Baxi boiler models allow homeowners to perform a reset for specific faults. However, the correct reset procedure depends on the model and displayed error code.
Follow the manufacturer's instructions and never repeatedly reset a boiler that continues to lock out. Do not attempt a reset if you suspect an unsafe condition.
Repeated pressure loss can be caused by a water leak, expansion vessel problems or other heating-system faults.
If you regularly need to restore pressure, arrange professional diagnosis rather than continually topping up the system.
Read our boiler losing pressure guide for more information.
A Baxi boiler may fail to fire up because of low system pressure, incorrect heating settings, an ignition problem or another fault.
Check the displayed code, thermostat settings and any homeowner checks permitted by the manual. Persistent ignition faults should be investigated by a qualified engineer.
Baxi boiler repair costs depend on the fault, boiler model, replacement parts, labour and whether additional diagnostic work is required.
A straightforward issue may cost less to resolve than a fan, pump or electronic control fault. An engineer can advise on repair options once the problem has been diagnosed.
Contact Keystone London to discuss your boiler fault.
Not every displayed code requires a repair. Some problems can be resolved through basic homeowner checks described in the user manual.
However, work involving the gas appliance and its gas or combustion components must be carried out by an appropriately qualified, Gas Safe registered engineer. Persistent lockouts, overheating and internal component faults should be professionally assessed.
Keystone London provides professional boiler fault diagnosis and repairs across London. If your boiler is showing a persistent error code or repeatedly locking out, contact our team for assistance.